Jeep Forums

On Saturday June 19th, aFe will be holding our quarterly parking lot sale. If you are in Southern California, please come by and check out the big savings on all aFe products including intakes, filters, exhaust, intake manifolds, intercoolers etc. All aFe products are available at special discounts.

The 4BT is not a bad decision put in a jeep. More power, better gas mileage. The Cummins shake lets me know the motor is still there when I crank it up EVERY morning to go to work. It is a very reliable motor, easy to work on (if I had to). The cost of the swap compared to gas savings will pay o

The 4BT is not a bad decision put in a jeep. More power, better gas mileage. The Cummins shake lets me know the motor is still there when I crank it up EVERY morning to go to work. It is a very reliable motor, easy to work on (if I had to). The cost of the swap compared to gas savings will pay o

OK, simple question here....is there a special tool required to install the bushings on the end of leaf spring or do they just slide right in? I haven't gotten the new parts yet, but just asking out of curiosity ahead of time.

So who on here's going? I know they have a rock crawling event and mud drags and a whole buncha different stuff going on with in the 4 days. It's in Mariaville NY.

I just reinstalled the a/c and heater control assembly after having to remove it for some other unrelated under the dash work. The a/c worked fine prior to this. After taking it out and putting it back in, no air comes out. No hot, no cold. NOTHING. I also removed the defroster nozzle. Doubt this h

Full restoration Jasper Performance Crate AMC360 (350+HP) Turbo 400, Dana300 Transfer case 3" Super lift suspension(new springs,bushing,shackles) Complete new interior: Seats, Carpet, Dash, Gauges 33 x 12.50 x 15 BFG AT Rhino lined bed Headers with dual exhaust and Turbo Mufflers Warn Bumpers T00 MU

I have a 1987 YJ that I just had a brand new AX-15 transmission put in . I purchased it from "Advance Adapters" in CA. For the transmission fluid they gave me a Chrysler part # which turned out to be nothing but regular 10W40 Penzoil motor oil and suggested ATF+4 for the transfer case. I've read a

Just purchased an o-10 JK sport (2dr). I want to put 34" M/T's on her with a small lift. My concern then would be the integrity of the stock braking system. Has anyone had (stock) brake issues with a larger tire setup? -Also, later down the road I want to re-gear to 4.10 or higher. At what point sh

I HAVE A 46 CJ2A PROJECT AND AM LOOKING TO SWAP AXELS. I HAVE COME ACROSS AXELS OUT OF AN 87 CAMANCHE METRIC TON. I KNOW THE FRONT SHOULD BE A DANA 30 AND I BELIEVE THE REAR ON THE METRIC TONS WERE DANA 44'S WOULD THESE BE A GOOD CHOICE FOR THE SWAP AND IF SO WOULD I HAVE TO SHORTEN THEM ? HOW MUCH

is there a more reliable stock tranny made for a jeep CJ? I'm looking at starting a project in the near future, was leaning towards an '86 CJ-7, because I thought that had the best stock options in the drive train like Dana 44 on both ends and a dana 300 transfer case. For some reason I thought tha

Anyone tell me if the leaf springs from a 79 Ford Bronco will fit on an 89 XJ without mods?

My blower switch does not direct the air to the floor or dash anymore, only goes to the windshield, is this a switch problem or is there some type of deflector issue that sends the air down to the floor?

I love the magazine but I'm new to the forum so, hello all and thanks in advance for any help you may be able to give. I have a restored fiberglass body 78 CJ-7 with a 304 and a 4 speed. The motor is mostly stock except for an Edelbrock intake, Edelbrock four barrel carb, a mild RV cam and headers.

hi, I have a 1995 jeep wrangler rio grande with the 2.5l engine and since I bought it about a year ago its been making this whining noise when I'm going 25-40mph in 2nd 3rd and 4th gear. it only makes the sound when I hit the gas so I don't think it is the tranny but maybe the output shaft bearing h

8 Comments, last updated on May 22, 2010 by Giovanni

10 Comments, last updated on May 21, 2010 by Bought Out

[bold]Big Rubbers held their Spring Thaw event in Johnstown Pa. Saturday May 15th was the car show, Rib cook off, Jeep Teeter Totter, log obstacle, RTI ramp, and concret obstacles. Sunday was a day of wheeling on the Clubs privet property. At least 4 other Pa. clubs joined the fun. My hats off to t